Diesel Injector Copper Washers Seal Sealing Rings Kit Ports Assortment 150pcs

Product Information

In high-pressure diesel systems the injector has to seat into the seal perfectly, otherwise, a pressure bypass can occur, which will reduce the compression in that cylinder and provide very reduced performance, even when a new injector has been installed. (This will often produce degraded combustion). If you're an older motorist, you may associate the job of feeding fuel into the engine with the carburettor. However, fuel injectors have been gradually taking over from carburettors since the 1990s. They're simply cleaner and more efficient. How to spot a faulty fuel injector Code work: Using general diagnostic software, code the injectors to the car. You need to input the four unique codes for the injectors. You did write those down, didn’t you? If your vehicle's engine has started misbehaving in certain ways, it may need replacement fuel injectors. At Halfords, we're one of the UK's leading suppliers of all car parts with an extensive selection available online—and at our 600+ Halfords garages nationwide. Feed pipes: Remove the four injector feed pipes. Technically, these should be renewed, being part of the high-pressure system. Close inspection shows them to be perfect to reuse.

Seat repair:When the injector seat in the head is contaminated or damaged, it can be cleaned or refaced by inserting a special cleaning or cutting tool down through the injector opening to re-create a flat, sealable face for the new sealing washers. When fuel injectors are working properly they adjust the amount of fuel being introduced to match the variable airflow. If kept clean and well-maintained, your fuel injectors can also maximise the car's fuel efficiency and minimise pollution. Last job: With a hot engine, the software automatically sets and adjusts the injector adaption values over five set points according to engine parameters.Torque matters: The clamp bolts are stretch bolts, so correct and accurate tightening is critical. When set, they stretch a set amount, but remain elastic. Torque first to 8Nm. Acontemporary diesel engine relies on high-pressure injector technology, and the Puma engine is no different. This Ford in-line four-pot diesel originated in the Duratorq TDCi for the Ford Transit, but it was used by several other manufacturers, including Land Rover in the Defender from 2007. Cleanliness within the fuel system is critical so, after removing pipes and components, ensure dirt cannot enter the resulting openings. The injector holes in the head also need to be cleaned to prevent dirt dropping into the engine, as explained in the captions. Unplug the power: Next, unplug the injector loom feeds, then lever the plastic covers off from the loom mounts. These also cover the injector clamp fixing bolts.

Other problems include: water in the fuel which can cause the injector nozzles to balloon; carbon can build around the injector nozzles; and combustion gas can blow up past the injector body if the copper seal between the injector and cylinder head fails, exacerbated by the injector clamp bolts stretching. Second step: After torque tightening, the bolts need a further rotation of 180 degrees. This angle precisely sets the bolt torque, based on thread pitch and calculated stretch. Fuel injectors often start to cause problems when the nozzles get clogged. Symptoms of a faulty fuel injector include:

Injector & Glow Plug Removal

The air intake system controls the airflow into the engine and the fuel injector delivers the fuel, so they have to work in harmony to keep your motor running. Replaced clips: These are the spill pipe locating clips we found missing on our vehicle. They are brittle, and not easy to buy, so do take care with them. It is possible to recondition the injectors, but results can vary, so consider the value of simply replacing old with new. New injectors need to be coded to the car using diagnostic software via the OBD port. There are two things to be aware of when changing injectors. Carbon deposits can form on injector tips, making their extraction from the head difficult. And the mating seat in the head must be free from dirt and deposits when refitting the new injector. Like all of us working on our Land Rovers, consider carefully if you can cope with either issue. If not, then it might be time to take the car to a specialist. There’s no shame in that: wise enthusiasts understand the limits of their abilities.

ED EVANS SAYS: Injectors tend to be forgotten about until there’s an engine running problem and, of course, not all problems are down to injectors. A multitude of other engine defects can affect the state and lifespan of the injectors, so it’s vital to keep the engine correctly maintained and properly used to avoid replacement of these relatively expensive items. Before thinking about replacing injectors, the engine needs to be inspected by a good specialist to confirm the cause of the symptoms, and the full effects. On this 120,000-mile 2.4 Defender belonging to Karl Jane, another garage had previously reconditioned and refitted the injectors. But after they were coded to the car, the adaption values were way out, which would ultimately mean the injectors weren’t calibrated accurately at the ECU. Rather than cope with compromised performance, Karl opted to have new units fitted, this time by IRB Developments, where Ian Baughan now shows us the procedure for injector renewal on this 2010 Defender 90. BMW 114D, 116D, 118D, 120D, 216D, 218D, 220D, 316D, 318D, 320D, 420D, 518D, 520D, X1 18D, X1 20D, X2 18 D, X2 20D, X3 18D, X3 20D, X4 20D 2012- Follow the process: Plug is located in the tip hole to prevent dirt ingress. Then helical brush (inset), spinning in drill, cleans the sides of the injector bores in the head.New injectors: Each injector has a unique code on the top. Write each one down, noting which injector is in which cylinder. You’ll need that code for the software, later. Where are they?The 2.4 Puma engine bay: like all modern cars, the injectors are hidden under the plastic cover. Two bolts, off it comes, and we can see everything.